Skip to content
Castleton, NY  /  Mon to Fri, 7:30am to 4:00pm
Upstate NY · VT · W. MA · CT 518.766.7676 info@total-tool.com
Home/Equipment/Waste Oil Heaters & Boilers
EnergyLogic waste oil heater installed by Total Tool

Equipment  /  Facility & heating

EnergyLogicAuthorized dealer

Waste oil heaters.Turn used oil into heat.

EnergyLogic furnaces and boilers turn the used oil your shop already generates into heat for the bays. Total Tool installs them, cleans and tunes them every season, and services Clean Burn units too.

Cleanings book up before heating season. Get on the schedule early.

Installed by Total Tool
5–90 weightUsed oil, ATF, synthetics
Up to 9,000 sq ftFrom a single furnace
StainlessHeat exchanger, built for decades
Serviced hereEnergyLogic and Clean Burn

Three questions

Size your heater

Square footage picks the model, and your used oil decides how far it carries you. The site visit confirms both before anything is ordered.

Floor area to heat

How you want the heat delivered

Used oil you generate per month

Answer all three

Your heater shows here

Pick your floor area, how you want the heat, and roughly how much used oil you collect.

Browse the range

Featured heaters and boilers

Pick a model to add it to your request, or ask about models not shown here.

Ways to set it up

Built around your building

EnergyLogic's layouts cover most shops. We plan the version that fits yours at the site visit.

Complete system layout
Complete systemFurnace mounted on its tank, with everything needed for install.
Remote tank layout
Remote tankHeater in one spot, tank out of the way, with transfer accessories for long runs.
Multiple furnaces layout
Multiple furnacesLarger buildings zoned with several units fed from one tank.
Furnace plus HVLS fan layout
Furnace plus HVLS fanA fan pushes warm air from the ceiling back down to the floor.
Radiant floor layout
Radiant floorA boiler heats the slab from the ground up, and can melt ice on drives.
Stacked boilers layout
Stacked boilersA small footprint lets boilers stack on racks in tight rooms.
Domestic hot water layout
Domestic hot waterAn optional coil heats water for restrooms, wash bays and more.

The technology

Engineered for used oil

Used oil is inconsistent: different weights, water in the tank, sludge on the bottom. EnergyLogic's patents are aimed squarely at that problem.

Fuel range
5–90Wcrankcase oil, ATF, hydraulic fluid, #2 fuel oil, diesel and synthetics

No manual adjustments

A patented side-suction metering pump delivers consistent fuel regardless of fuel type, and the patented Accutemp® preheater handles the widest range of viscosities.

Fuel pickup
6 in.above the bottom of the tank

Oil in, water and sludge out

The elevated pickup draws above the water and sludge layer, through a spin-on stainless mesh filter, so only used oil reaches the burner.

Air supply
Built inintegrated air compressor

No shop air required

The on-board compressor means the heater runs around the clock without depending on your shop air system.

Heat exchanger
Stainlessexclusive to EnergyLogic

Built to last decades, not years

Designed to prevent corrosion, warping and weld breakage, with an open design and swing-away burner that make cleaning straightforward.

See it in action

A closer look at EnergyLogic waste oil heating, from EnergyLogic.

The rules

Burning used oil, by the book

Federal EPA rules let a shop burn its used oil for heat without being treated as an off-specification used oil burner, as long as three conditions are met.

01The heater burns only used oil you generate, or used oil from household do-it-yourself oil changers.
02The heater is designed for a maximum of 0.5 million BTU per hour.
03The combustion gases are vented outside.

Every EnergyLogic furnace and boiler is rated at or under that limit, and the largest boiler tops out at 499,000 BTU per hour. Source: 40 CFR 279.23. State and local rules can add requirements.

Side by side

Furnace or boiler

Both burn the same used oil. The difference is how the heat reaches the floor.

Warm-air furnaceHydronic boiler
Heat deliveryWarm air blown from overheadHot water to radiant floors or a hydronic loop
Range75,000 to 350,000 BTU/hr200,000 to 499,000 BTU/hr
MountingCeiling-hung or tank-mounted (12 ft minimum ceiling tank-mounted)Floor-standing, tied into the water system
Good to knowIntegrated compressor, no shop air neededLow pressure (30 psi max); return water must stay above 140°F
Best fitOpen service baysRadiant floors and existing hot water systems

The vendor

Why Total Tool backs EnergyLogic

EnergyLogic

Patented where it matters

EnergyLogic has been on the leading edge of waste oil combustion from the start, and its patents sit exactly where used-oil heaters usually fail: fuel delivery, preheating and the heat exchanger. The result is a heater that handles a wide range of used oils without manual adjustment.

Total Tool sells, installs and services them, and the same crews do the annual cleaning and combustion tune-up that keeps the warranty and the burner happy.

UL listedWarm-air furnaces from 75,000 to 350,000 BTU per hour.
Patented fuel systemSide-suction metering pump and Accutemp® preheater handle oils up to 90 weight.
Stainless heat exchangerDesigned to resist corrosion, warping and weld breakage.
WarrantyTwo years on parts with registration, and ten years on the combustion chamber, five full and five prorated.

Why buy it here

Installed, cleaned and tuned every season

Total Tool has equipped shops across upstate New York, Vermont, western Massachusetts and Connecticut since 1983. A waste oil heater runs best with a yearly cleaning, and our service crews do it before the cold arrives.

  • Sizing, placement and ceiling height checked before anything ships
  • Flue, fuel tank and pump installed by our own crews
  • Annual cleaning and combustion tune-up before heating season
  • Burner service and replacement parts
  • Financing, and quotes formatted for purchase orders

We service both

EnergyLogic
Clean Burn
Annual cleaning, tune-ups and repairs for EnergyLogic and Clean Burn heaters and boilers, whoever installed them.

Common questions

Before you buy a heater

Is it legal to burn used oil in a shop heater?

Under federal EPA rules, yes, when the heater burns only oil you generate or oil from household do-it-yourselfers, is designed for no more than 0.5 million BTU per hour, and vents outside. State and local rules can add requirements.

What can an EnergyLogic heater burn?

Crankcase oils, ATF, hydraulic fluid, #2 fuel oil and diesel, from 5 to 90 weight, including synthetics.

Can I burn used oil from other businesses?

Not under the federal on-site space heater rule. It covers oil you generate yourself and oil from household do-it-yourselfers only.

How often does it need service?

Once a year. We clean the heat exchanger and burner and do a combustion tune-up before heating season, which is the best time to book.

Do you service Clean Burn heaters?

Yes. We clean, tune and repair Clean Burn and EnergyLogic heaters and boilers, whoever installed them.

How high does the ceiling need to be?

A tank-mounted EnergyLogic furnace needs at least a 12-foot ceiling. We check clearances and the flue route at the site visit.

Request a quote or cleaning

Tell us about the building

Square footage, ceiling height and roughly how much used oil you collect. For a cleaning, just the make and model.

01Tell us the building and your used oil, or the heater you need serviced.
02We size the heater, flue, tank and installation as one number, or book your cleaning.
03Our crews install it, then clean and tune it every season.

Interested in financing? Ask for payment options → · How financing works

No heat? Call. It is faster than the form.

Heater quote or cleaning

Tell us what you need and what you run today so the right tech calls you back.

How financing works · We reply within one business day.

Call now Request a quote