Equipment / Air & lubrication
Authorized dealerAir compressors.Built for longevity.
Ingersoll Rand's Next Generation RS Series rotary screws and two-stage cast iron reciprocating compressors, built to boost productivity, lower operating expenses and extend equipment life. Total Tool sizes them, pipes them with Prevost aluminum and keeps them running.
Two questions gets you a working CFM number.

Two questions
How much air does your shop need?
Compressors are sized on airflow (CFM), not just horsepower. Two answers give you a starting point, and the site visit confirms it before anything is ordered.
Techs pulling air at the same time
The air-hungry extras
Rough sizing
A starting point, not a spec. Piping runs, elevation and duty cycle get confirmed at the site visit.
Answer both
Your CFM shows here
Pick a crew size and the extras, and we will put a working number and a compressor class next to it.
Browse the range
Featured compressors
Ingersoll Rand rotary screw and two-stage reciprocating, Industrial Gold cube systems, and Prevost aluminum to deliver the air. Pick a unit to add it to your request, or ask about models not shown here.
Ingersoll Rand rotary screw
Next Generation RS SeriesAirends with an optimized rotor profile, V-Shield™ leak-free construction and Xe-Series controllers you can reach from any current web browser.

Shown with the Total Air System: integrated dryer and 3-in-1 heat exchanger for clean, dry air in a single package.
15–30 HP · TAS option
Fixed or variable speed. Up to 16% improved efficiency and 21% greater airflow from the Next Generation airend.
40–100 HP
A compact, complete, easy-to-use rotary screw package, tank-mounted and ready to plumb.
5–15 HPIngersoll Rand two-stage
Cast iron reciprocatingDurable cast iron construction and 100% continuous-duty ratings, with pumps designed for over 15,000 hours of trouble-free use.

5 or 7.5 HP, 175 psig maximum operating pressure and an 80-gallon ASME receiver. Value and Premium feature packages.
5–7.5 HP
The next pump up: the same individually cast cylinders and overhung crankshaft for busier shops.
10 HP
Diesel-powered for service bodies, yards and job sites without shop power.
Mobile & remoteIndustrial Gold
Building air since 1996Rotary screw cube systems with the airend, motor and controls in one compact frame, for shops that want screw performance in a smaller footprint.
The piping
PrevostAir is only as good as what carries it. Prevost aluminum runs don't corrode, don't leak at the joints and reconfigure when the shop does.
Every compressor above lands with piping, startup and a maintenance schedule quoted as one number.
The technology
The technology behind the air
Horsepower sells compressors; duty cycle, dryness and monitoring are what shops live with. Total Tool quotes the current Ingersoll Rand lineup with all three specified up front.
More air from the same horsepower
The RS line is Ingersoll Rand's current screw generation: V-Shield™ leak-free construction with PTFE lines and O-ring face seals, premium coolant, and airends built for years of continuous duty.
Dry air in one footprint
Moisture ruins paint work and shortens tool life. The TAS option integrates the dryer and a 3-in-1 heat exchanger into the compressor cabinet, so clean, dry air arrives as one install instead of three.
A pump built for 15,000 hours
The two-stage cast iron pumps are designed for 15,000 hours. Start on the All Season Select synthetic kit and the pump warranty extends with it — the maintenance schedule and the paperwork both come from us.
Remote monitoring from any browser
Xe-Series controllers deliver increased control functionality through an intuitive interface, with remote access from any common, current web browser — so service alerts arrive before small problems become downtime.
Side by side
Reciprocating or rotary screw
Both are built for continuous duty. The difference is noise, air quality, controls and how the cost lands over the years.
| Two-stage reciprocating | Rotary screw (RS) | |
|---|---|---|
| Pressure | Up to 175 psig (2475) | 125–150 psi typical |
| Noise | Louder; wants its own corner | Enclosed cabinet, conversation nearby is fine |
| Air quality | Standard; dryer added separately | TAS option: dried and filtered in the cabinet |
| Best fit | Smaller shops, single-shift service | Busy service departments, paint and multi-shift work |
| Maintenance | Simple and rebuildable for decades | Scheduled service, remote-monitored by Xe |
| Cost logic | Lower up front | Lower per CFM over the years |
The vendors
Why Total Tool backs these brands



Ingersoll Rand, Industrial Gold and Prevost
Ingersoll Rand's Next Generation RS Series is built to boost productivity, lower operating expenses and extend equipment life, alongside its two-stage cast iron reciprocating line. Industrial Gold, building air since 1996, adds rotary screw cube systems, and Prevost supplies the aluminum piping that delivers the air without leaking it away between the tank and the tool.
The system is the product: we size the compressor to your real CFM, run the drops to where the work happens, start it up, and service it for its whole life — every make, not only what we sold.
Why buy it here
One local team, from quote to service
Total Tool has equipped shops across upstate New York, Vermont, western Massachusetts and Connecticut since 1983. The same team that sizes your compressor installs it, starts it up and services it for as long as you run it.
- Placement, ventilation and electrical planned before anything ships
- Prevost piping and drops run to where your techs work
- Startup, break-in and a maintenance schedule set to your hours
- Repairs on every make of compressor, not only ours
- Operator training for your techs at handoff
- Financing, and quotes formatted for purchase orders

Goes with this
Air feeds everything else
Common questions
Before you buy air
Reciprocating or rotary screw?
Both are rated for continuous duty. Reciprocating is the lower-cost, rebuildable choice for smaller shops; rotary screw is quieter, delivers more air per horsepower and adds options like the integrated dryer and remote monitoring.
What size compressor does my shop need?
Size on CFM, not horsepower. The two-question helper above gets you a working number; the site visit checks piping runs, elevation and what you are really running before anything is ordered.
Do I need an air dryer?
If you paint, calibrate or run air tools you care about — yes. Wet air ruins finishes and rusts tools from the inside. The TAS option builds the dryer and filtration into the compressor cabinet.
Our compressor died and you did not sell it to us. Will you fix it?
Yes. We service and repair every make. If it is past saving, we will tell you that too, with a number for what replacing it properly costs.
How loud is a rotary screw?
Quiet enough that shops put them near the parts counter. The enclosed cabinet holds most units to normal-conversation range; placement during the site visit handles the rest.
What does installation include?
Placement and ventilation, the Prevost piping and drops, electrical coordination with your contractor, startup and break-in, and a maintenance schedule — quoted as one number with the machine.
Request a quote
Tell us the bays and the tools
Bays, techs pulling air at once, and what you run today. That is enough to size it right the first time.
On your request
Interested in financing? Ask for payment options → · How financing works
Compressor down? Call — 518.766.7676 gets a tech moving.


