
Equipment / Air & fluid
Authorized dealerLubrication equipment.Every fluid, bay to tank.
Oil, ATF, grease, coolant, washer fluid and DEF, pumped from bulk storage to a metered handle at every bay. Total Tool lays out the lube room, runs the piping and hangs the reels.
Starting fresh, adding reels or replacing a pump. All three start the same way.
The system
Six steps from tank to bay
A lube room is one system, not a pile of parts. Pick a step to see what does the work.
Step 01 · Store
Bulk storage sized to your volume
Fresh oil and ATF in bulk tanks or ready-made tank packages, with waste oil stored separately. The tank room decides everything downstream.
- Single and double wall options
- Fresh and waste oil packages
Step 02 · Pump
Move fluid on shop air
Air-operated ratio pumps push oil from the tank to the bays. They run on compressed air, so the pumps and the compressor get sized together.
- Stub and drum pump options
- Sized to hose length and handle count
Step 03 · Pipe
Fluid delivered where the work is
Piping runs overhead from the tank room to each bay drop, laid out before anything ships so the runs are short and the drops land where techs stand.
- Laid out at the site visit
- Installed by our own crews
Step 04 · Reel
Hoses up and off the floor
Reels at each bay keep hoses retracted and out of the walkway, one per fluid or as dual-arm reels for tight spaces.
- Oil, grease, air and water reels
- Ceiling, wall or pedestal mounting
Step 05 · Meter
Know what went into every car
Digital metered handles measure what is dispensed at the bay, so the quart count on the repair order matches the fluid that left the tank.
- Digital and mechanical options
- Non-drip tips
Step 06 · Collect
Used oil back to a tank
Drains and receivers move used oil into a waste tank, where it can be hauled away or burned for heat in a waste oil heater.
- Waste oil tank packages
- Pairs with an EnergyLogic heater
Browse the range
Featured lubrication equipment
Grouped by fluid. Pick equipment to add it to your request, or ask about anything not shown here.
Motor oil and ATF
The core of the lube roomPumps, reels, metered handles and oil bars for the fluids that move the most volume.

Air-operated stub pumps that mount in the tank and push oil and ATF to every bay.
Air-operated
Platinum Series double-arm and Advantage Plus reels keep hoses retracted and off the floor.
Single or double-arm
Digital metered handles with non-drip tips measure what goes into each vehicle.
Digital metering
Multi-spigot metered oil bars for quick lube and top-off stations.
Quick lubeWaste oil
The other half of the oil changeCollect used oil cleanly and get it to a tank, a hauler or a heater.
Tank packages
Fresh oilComplete packages that skip most of the installation work: unpack, connect air, fill and run. Bigger shops get separate tanks, pumps and piping laid out for the building.
Air, grease, coolant and DEF
Everything else in the bayThe rest of the fluids a service bay handles, on the same system.
What makes it work
A lube room that pays for itself
The equipment is simple. The layout is where the savings live.
Bill what you dispense
Metered handles close the gap between what leaves the tank and what lands on the repair order.
Pumps and compressor sized together
Air-operated pumps depend on steady air, so we check the compressor while we plan the lube room.
Less hose, fewer steps
Tank room placement and drop locations decide how far techs walk and how much fluid sits in the lines.
Waste oil becomes fuel
Collected used oil can feed a waste oil heater instead of a hauler, which turns the lube room into part of the heating plan.
Side by side
Tank package or custom system
Most shops land on one of two setups. Here is how they compare.
| Tank package | Custom bulk system | |
|---|---|---|
| Setup | Tank, pump and hardware as one unit | Separate tanks, pumps and piping |
| Install work | Minimal: connect air, fill and run | Planned and piped to each bay |
| Fluids | One or two per package | As many as the shop runs |
| Best fit | Smaller shops and single fluids | Busy service departments and fleets |
The vendor
Why Total Tool backs American Lube

A full line, stocked on both coasts
American Lubrication Equipment started in a small downtown Baltimore office and grew into a full-line lubrication supplier with warehouses on both coasts. Its range covers oil, waste oil, grease, antifreeze and washer fluid, air and water, and DEF, so one vendor supplies the whole lube room.
Total Tool lays the system out, installs it and stays on as your local contact, with American Lube's field and technical support behind the equipment.
Bulk storage and fueling
Tanks and fueling, from the same team
Storage tanks and fueling equipment, quoted and installed with the rest of the fluid system.

Steel storage tanks for fuel, oil and waste oil.

Fueling nozzles, swivels and breakaways for fuel islands and fleet yards.
Why buy it here
One local team, from quote to handoff
Total Tool has equipped shops across upstate New York, Vermont, western Massachusetts and Connecticut since 1983. A lube room touches the air system, the bays and the heat, and we plan all three together.
- Lube room and reel locations laid out before anything ships
- Piping and drops run by our own crews
- Pumps and compressor sized together
- Waste oil collection tied into a heater if you want one
- Financing, and quotes formatted for purchase orders
One system

Common questions
Before you plan a lube room
Do I need a tank package or a custom system?
Tank packages suit smaller shops and single fluids with minimal install work. Busier shops running several fluids usually need separate tanks and piping laid out for the building. We recommend one after the site visit.
Do the pumps need shop air?
Most do. Air-operated pumps run on compressed air, so we check your compressor while planning the lube room.
Can you use my existing tanks or reels?
Often, yes. We look at what you have at the site visit and quote only what needs replacing.
Can waste oil collection feed a heater?
Yes. Collected used oil can go to an EnergyLogic waste oil heater instead of a hauler, and we install both.
Can you quote to a purchase order format?
Yes. Quotes can be formatted for PO and procurement requirements.
Request a quote
Tell us about the lube room
The fluids you dispense, how many bays, and where storage can go. That is enough to lay it out properly.
On your request
Interested in financing? Ask for payment options → · How financing works
Photos of the tank room and bays help us plan the piping.




